UEEDV0003 — Install and connect cabling for direct access to telecommunications service

1 Prepare to lay and connect cabling for direct access to telecommunication services

• 1.1Work health and safety (WHS)/occupational health and safety (OHS) requirements and workplace procedures for a given work area are identified, obtained and applied
• 1.2WHS/OHS risks are identified and risk control measures and workplace procedures are followed in preparation for the work
• 1.3Remote power feeding is identified and risk control measures prepared
• 1.4Scope of work is determined from documentation and/or discussions with relevant person/s
• 1.5Cable routes are planned within the constraints of the building structure, significants and regulations
• 1.6Earthing requirements are determined with existing earthing arrangements and cable system earth upper and lower resistance limitations
• 1.7Advice is sought from relevant person/s to ensure work is coordinated effectively with others
• 1.8Sources of materials required for work are checked in accordance with routines and workplace procedures
• 1.9Tools, equipment and testing devices required to carry out work are obtained and checked for correct operation and safety

2 Lay and connect cabling for direct access to telecommunication services

• 2.1WHS/OHS risk control measures and workplace procedures for carrying out the work are followed
• 2.2Installed support structure is checked to ensure cable is protected against damage during installation and general operation
• 2.3Sufficient excess is allowed at cable ends to facilitate termination
• 2.4Telecommunication outlet ends of cable are uniquely labelled to match identifier at originating location in accordance with relevant industry standards
• 2.5Cable is placed and secured to maintain safety and interference segregation in accordance with relevant industry standards
• 2.6Cable ties are tightened without damage to cable sheath or transmission impairment and trimmed flush in accordance with workplace procedures
• 2.7Cables are installed as catenaries or supported by catenaries in internal and external environment to meet above ground clearances and clearances from hazardous electrical services in accordance with relevant industry standards
• 2.8Cables are installed underground to meet depth of cover and segregation from hazardous electrical and relevant services in accordance with relevant industry standards
• 2.9Over-voltage protection devices are fitted to all cable pairs, as required, to suppress voltage surges with devices protectively earthed in accordance with relevant industry standards
• 2.10Telecommunications reference conductor (TRC)/communications earth system (CES)/earth wire insulation is protected and segregated against damage in accordance with relevant industry standards
• 2.11Workplace procedures for referring unplanned events to immediate supervisor for directions are followed
• 2.12Cabling is installed without waste of materials, energy, services, damage to apparatus and the surrounding environment
• 2.13Quality checks are carried out to ensure cabling is in accordance with relevant industry standards

3 Terminate, inspect and test cables and earth wires

• 3.1WHS/OHS risk control measures and workplace procedures for carrying out the work are followed
• 3.2Cable sheath is removed to allow for correct termination length without damage to underlying conductors and relevant insulation
• 3.3Network termination device is installed and cable pairs sequentially fanned for termination in accordance with manufacturer specifications
• 3.4Conductors are terminated with colour code sequence using relevant termination tools in accordance with manufacturer specifications
• 3.5Cable shield is earthed in accordance with manufacturer specifications and relevant industry standards
• 3.6Visual inspection is conducted to confirm termination colour code sequence prior to end-to-end testing of wire and pair termination integrity
• 3.7Cable pairs are inspected, tested and labelled to provide accurate identification in accordance with relevant industry standards
• 3.8TRC/CES/earth wires are terminated with connectors in accordance with relevant industry standards and manufacturer specifications
• 3.9TRC/CES/earth wire continuity is maintained throughout and interface requirements and electrical systems are observed
• 3.10TRC/CES/earthing installation is inspected and tested for continuity, insulation resistance and conductive resistance in accordance with industry standards
• 3.11Compatibility of alterations with existing systems and new work is confirmed and tested in isolation and integrated with existing systems
• 3.12Workplace procedures for referring unplanned events to immediate supervisor for directions are followed
• 3.13Cabling is terminated without waste of materials, energy and/or damage to apparatus, the surrounding environment and/or services
• 3.14Quality checks are carried out and defects rectified to ensure cabling is in accordance with workplace procedures and relevant industry standards

4 Complete cabling work records and reporting

• 4.1WHS/OHS work completion risk control measures and workplace procedures are followed
• 4.2Worksite is cleaned and made safe in accordance with workplace procedures
• 4.3Cabling completion advice is documented and reported in accordance with workplace procedures and relevant industry standards

What does an assessment tool for UEEDV0003 need to cover?

To satisfy the Principles of Assessment and Rules of Evidence, an assessment for UEEDV0003 needs to address all 120 unit components: 4 elements with 39 performance criteria, 20 performance evidence requirements, 61 knowledge evidence requirements, and the foundation skills. A coverage matrix mapping each question and task to these components is what an auditor looks for.

How does Auditori generate an assessment tool for UEEDV0003?

Auditori pulls the current release of UEEDV0003 from training.gov.au and generates a complete package: candidate assessment, assessor guide with model answers and observation criteria, and a coverage matrix mapping every component. A suitably qualified person then reviews and approves the draft in a built-in workflow — consistent with ASQA's guidance on AI use in VET — before export as branded PDF and editable Word.

Is the first assessment tool really free?

Yes. Every new account includes one free credit — enough to generate the complete assessment tool for UEEDV0003 — with no card and no subscription required. After that it's pay-as-you-go per unit.

Can I check my existing UEEDV0003 assessment instead of generating a new one?

Yes — upload your existing assessment or learner guide and Auditori maps it against every element, performance criterion, PE and KE of UEEDV0003, showing exactly what's covered and what's missing. Mapping costs a quarter of a credit.