CPCPCM3023 — Fabricate and install non-ferrous pressure piping

Generate a complete, audit-ready assessment tool for this unit in minutes: candidate assessment, assessor guide with model answers, and a coverage matrix mapped to every component below. Reviewed and approved by your qualified person, exported under your branding.

Generate CPCPCM3023 free See a real sample

Every new account includes a free credit — no card, no subscription.

What an assessment for CPCPCM3023 must cover

32 assessable components: 4 elements (12 performance criteria), 12 performance evidence and 8 knowledge evidence requirements. An audit-defensible tool maps every question and task back to these — that mapping is the coverage matrix Auditori generates alongside the assessment.

Elements & performance criteria

1 Identify installation requirements.

1.1Access, read and determine requirements to fabricate and install non-ferrous pressure piping from relevant job plans and specifications, codes, Australian standards, manufacturer’s specifications and jurisdictional requirements.
1.2Identify and apply workplace policies and procedures, work health and safety (WHS) and environmental requirements.

2 Prepare for work.

2.1Create a materials list and collect materials.
2.2Set up silver brazing equipment according to workplace and WHS procedures.
2.3Select and check serviceability of appropriate tools and equipment including personal protective equipment (PPE).

3 Fabricate, install and test pipe system.

3.1Set out pipelines and connection points according to drawings and specifications or job instructions.
3.2Use silver brazing equipment according to workplace and WHS procedures.
3.3Install pipework in accordance with relevant job plans and specifications, codes, Australian standards, manufacturer’s specifications and jurisdictional requirements.
3.4Test installed pipework according to s relevant codes, Australian standards, manufacturer’s specifications and jurisdictional requirements.
3.5Shut down and dismantle silver brazing equipment according to workplace and WHS procedures.

4 Clean up.

4.1Clear the work area, and dispose of, reuse or recycle materials in accordance with state and territory legislation and workplace policies and procedures.
4.2Clean tools and equipment, check for serviceability reporting any damage, store and secure.

Performance evidence

fabricating, installing and testing a DN20 copper line from a supply point to three fixed outlets, supported and clipped according to relevant job plans and specification, codes, Australian Standards, manufacturer’s specifications and jurisdictional requirements with a minimum:
one 15 mm mechanical bend
one 20 mm mechanical bend
one 15 mm spring bend
one 20 mm spring bend
one 15 mm capillary elbow
one 20 mm capillary elbow
one expanded silver brazed joint
one silver brazed copper to brass joint
two branch formed silver brazed joints
one mechanical flared joint
branches connecting at least two other non-ferrous materials, ensuring branches and bends are square.

Knowledge evidence

fabrication, installation and testing process for non-ferrous pressure pipe systems
relevant statutory authorities’ requirements and standards related to fabricating, installing and testing non-ferrous pressure pipe systems
effect of heat and other products on the properties of polymer pipe
types of non- ferrous materials, including joining techniques
hot works permit
how to access relevant information, including codes and standards
tools, materials and brazing equipment used to fabricate and install non-ferrous pressure piping
work health and safety (WHS) requirements to fabricate and install non-ferrous pressure piping.

Unit content sourced from training.gov.au — © Commonwealth of Australia, licensed under CC BY 4.0. Auditori is not affiliated with the Department of Employment and Workplace Relations.

See what you get before you start

Real, unedited Auditori output (RIIHAN201E shown), branded for a sample RTO:

Questions about assessing CPCPCM3023

What does an assessment tool for CPCPCM3023 need to cover?

To satisfy the Principles of Assessment and Rules of Evidence, an assessment for CPCPCM3023 needs to address all 32 unit components: 4 elements with 12 performance criteria, 12 performance evidence requirements, 8 knowledge evidence requirements, and the foundation skills. A coverage matrix mapping each question and task to these components is what an auditor looks for.

How does Auditori generate an assessment tool for CPCPCM3023?

Auditori pulls the current release of CPCPCM3023 from training.gov.au and generates a complete package: candidate assessment, assessor guide with model answers and observation criteria, and a coverage matrix mapping every component. A suitably qualified person then reviews and approves the draft in a built-in workflow — consistent with ASQA's guidance on AI use in VET — before export as branded PDF and editable Word.

Is the first assessment tool really free?

Yes. Every new account includes one free credit — enough to generate the complete assessment tool for CPCPCM3023 — with no card and no subscription required. After that it's pay-as-you-go per unit.

Can I check my existing CPCPCM3023 assessment instead of generating a new one?

Yes — upload your existing assessment or learner guide and Auditori maps it against every element, performance criterion, PE and KE of CPCPCM3023, showing exactly what's covered and what's missing. Mapping costs a quarter of a credit.

Related units

Your CPCPCM3023 assessment tool, in minutes.

First unit free. No card, no RTO registration, no subscription.

Generate CPCPCM3023 free